Your Search: "frame pack"

Refill pack for the Park Tool TPT-1 Tubeless Plug Tire Tool and other similar tools. These vulcanized rubber plugs are used to temporarily repair punctures in tubeless bicycle tire systems. Set of 5. NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.

The Odyssey stem bolt pack features 6 - 6mm stem bolts that are M8 x 1.25mm thread.

Park's Vulcanizing Patch Kit includes 4 round patches for small holes and 2 oval patches for wider cuts; a tube of self-vulcanizing glue that bonds the patches to your tube super securely; and sandpaper for preparing the punctured area for gluing. The kit comes in a small plastic box to fit in your seat bag or pack.

- Attaches to rear racks - Compatible with: Blinky 3,5,7 and Superflash - 25mm between each of the top horizontal holes (center to center) - Requires an "L bracket" that typically comes with a rear rack. If your rack is missing the L bracket, you can purchase Planet Bike's rack hardware pack

The solution to organizing cables instead of them looking like a tangled mess on your handlebar Comes in a pack of five in various colors

The new B-gap adjustment tool is simple and easy to use, allowing for a quick set up experience. Small enough to be able to pack in your ride bag or stash in your toolbox for repeated use, it is also industrially recyclable if you find you no longer have use for it. This is the most precise tool for setting up and adjusting your drivetrain.

It's always a good idea to have backup hardware. This is a replacement hardware pack for Portland Design Works Payload or Loading Dock rear racks. - 2x P clamps - 4x nyloc nuts - 4x hex bolts

- Replacement chain pin for 7- and 8-speed Shimano chains - 3 replacement pins per pack

Metal clips to hold Elite Bleed Kit syringes upright or at 90-degrees - Compatible with both DOT and mineral oil kits - 2 clips per pack

The Pro Internal Cable Routing Tool uses a rare earth magnet that attaches directly to cables, housing, hydraulic hose, and electronic shifting wire, and can be fed directly though difficult internal setups without the need for a separately routed "lead wire." - This pack includes replacement fittings to attach magnet to cables, housing, hydraulic hose, and electronic wire

- Replacement chain pins for Shimano 11-speed chains - Compatible with CN7900/7801 chains - 3 pins per pack

- Replacement pins for 9-speed Shimano chains - Compatible with CN-7700/HG92 chains - 3 replacement pins per pack

By using the accessory bolt mounts on a frame or fork, the Wald Standoff kit allows the user to space a basket or rack away from other components that would otherwise be in the way, like disc brake calipers. - 2 Phillips head frame bolts in 1.5-inch (38mm) length - 2 Standoff spacers in 1-inch (25.4mm) length

Jagwire's Aluminum Housing Connectors allow joining two sections of the same-size cable housings together in case you only have shorter sections and you need to make a longer one. It comes in 4 and 4.5mm diameters. Match the diameter of the housing sections on your bike. - Comes in a pack of 10

Features - Compatible with common wheel and tire sizes - Helps keep the back side of suspension fork bridges clean - Multi-color Giant logo sticker pack included

Jagwire's 5mm Anchor Bolt fits certain models and types of brakes and is used to secure the cable in place after adjusting it. It is made of plated metal for strength and durability. You get a pack of 25.

Protection where it's needed; Tube Tops can be placed virtually anywhere cable housing comes into contact with a bicycle frame. Designed to protect a frames finish Tube Tops can also be used to quiet cable slap.

Jagwire's Straddle Cable Carrier is for cantilever and centerpull brakes. It attaches to the end of the brake cable and is what the brake's straddle (also called transverse or crossover) cable attaches to. The Straddle Cable Carrier is made of light, corrosion-resistant and durable aluminum with a steel bolt. You get a pack of 10.

For BabySeat II Racks and MTX Tubular Racks (34.5 cm in length for small bike frames). - If you have a small frame bike and cannot install Topeak rack or BabySeat in recommended position (2 or 3 degrees from horizontal), please use the 34.5cm extra long mounting bracket arm for proper installation.

Adapter for direct mounting of the Fuel Pack or other equipment with screw connections. Are you planning to mount the Fuel-Pack or a bottle holder on your bike but find the threaded holes are not in the right place? The Offset-Plate 64 MM gives you a flexible way of adjusting the position of the Fuel-Pack, a bottle holder or other equipment with screw connections.

- Knee/elbow pad combo pack in a mesh bag - Available in multiple kid-approved designs

- Simplistic safety light combo pack designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - Both lights feature 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries each

- Bike rack RR 290 mm strut kit with hardware - Great for smaller frames - 4 bolts & nuts - 1 set/bag

Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. For water bottle, toe clip, fender and rack bosses. The TAP-8 is 5mm x 0.8 for use with water bottle, toe clip, fender and rack bosses.

Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. The TAP-9 is 6mm x 1mm for cantilever brakes and large fender bosses.

Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. The TAP-7 is 3mm x .5 for use with rear wheel drop-out alignment screws.

Jagwire's M7 Adjusting Barrel is a 7 x 1.0mm-threaded replacement cable-adjusting barrel. It's the right part for many older-style mountain bike brake levers. It comes in two models and is made of durable metal with a lockring for locking your adjustments. You get a pack of 10.

Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. The TAP-10 is a 10mm x 1mm thread, the same thread for the derailleur hanger.

Jagwire's Stick-On Cable Guides are made of lightweight aluminum with adhesive on the bottom. The aluminum lets them conform to any shaped frame tube and the adhesive holds fast. They come with Jagwire's C-Clips, nylon cable clips that snap onto the guides to hold the cables neatly in place. You get a pack of 4.

Planet Bike's Ozone ATB Comp Mini-Pump is a ride-saver. For easy pumping and fast fills, it boasts a locking T handle, an easy pumping action and a thumblock head (with a cap to keep the mud out). This great inflator fits all valves and is small enough to carry in a pack or pocket, or you can use the included frame mount.